Gazcw wrote:

MAF

Thanks 🙏
Does the car need “telling” it has a new one fitted? No fault codes before fitting or after.
Test drive tomorrow am.
I changed it as my old one was getting a little sooty underneath on outside. Some have tried ptfe tape but I thought it let’s order a new one from Duckworths and see how it compares on fit.
I’m all about preventative maintenance  Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

DrRob wrote:

Is that the air intake temperature sensor?

Thanks. I checked with an LR ex mechanic and he confirms it’s a sensor to monitor boost temperature. If it goes up too high a value then boost is backed off  Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

Last edited by DrRob on 21st Jun 2020 6:53pm. Edited 1 time in total

They aren’t the tightest of fit out of the box.

I did the one on mine as it was a bit sooty, can’t say it made a difference, and the new one was only slightly better seal wise. A couple of wraps of PTFE sounds like a decent idea so long as it’s secure and doesn’t get into the intake.....

I didn’t tell mine it had a new one. Don’t think there is a method for this in any case.👍🏻 There is nothing that can't be fixed with a hammer😜😜
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

Sorry, he also said no IID coding needed etc.
Agreed, didn’t feel massively tighter but all done  Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

Has the airflow temp sensor got any maker or spec markings on it?

If we could figure out its resistances or however it works, it may be possible to source an alternative and use something like this to dispose of the poor fitting, overly priced lump of plastic.

https://www.viperperformance.co.uk/silicon...-hose.html
[img]

Click image to enlarge

I’ll take a look at the old one and let you know  Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

Ok. The alternative is to cut the spring section off, leave the sensor in and use a piece of silicon pipe between the two.

I may look at that tomorrow. 2011 4.4tdv8 Vogue
Baltic Blue

Good idea too
I assume you have an old one to fettle? Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

No I haven't but I am in need of a new one I think as my soot levels are climbing too quickly.

Went to London yesterday and had 5 regens. I had ptfe tape on and when I removed today it was clearly oily and sooty.

So it is a few quid for a bit of silicone if possible to do or 120+ for another ill fitting connector. 2011 4.4tdv8 Vogue
Baltic Blue

I'd be tempted to buy a new one off Duckworths (quick delivery by Robin I might add) and then you have your old one to play around with an alternative solution. I think the easiest way will be to cut off the end with the seal/clip thus leaving the plastic pipe with sensor and "side pipe" intact and then find a wide bore silicone hose to bridge to the throttle body. There is a fair length of throttle body "metal" for it to cover too....
Also, with a new one on you can directly compare soot levels on the same trip to London if you do it again soon Gone to a good home: 2011 4.4 TDV8 Vogue SE Buckingham Blue with Ivory and clear glass = "Rory"
2025MY Defender D350 90 in Silicon Silver on coils
1974 Series 3 Lightweight = "Millie"
Many, many other Landies over the years
My preferred specialist: www.glenrands.co.uk
--------------------------------------------------

5 regens is a lot

. Cheers, Greg
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2011 Vogue SE 4.4 with lots of toys in Stornaway

kevinp wrote:

DrRob wrote:

How is the clip removed to remove the pipe?

It's a lot easier to get off if you remove the rubber hose completely from the intercooler first. Less chance of breaking that delicate water connection that goes over it. Then with a screwdriver gently pry the clip out of its locating slots. Just make sure you bend it to a complete circle before putting it back on with the split at the bottom.

Replied to your other post  Cheers
Richard

(there are no such things as an ordinary FullFat, an ordinary cat or too many tools)
2011 TDV8 Vogue Santorini Black
Gap IIDBT

JoolsB wrote:

Does anyone know the part number for the delicate water connection - I’ve just broken mine and need to get a replacement, can’t see it on the advanced factors site

LR029140  The older I get, the more I realise that people confuse wrinkles for wisdom