fullfatrr.com - View topic - Range Rover L322 - Stuck in Extended or Off Road Height

Advertise on fullfatrr.com »

Forum · Gallery · Wiki · Shop · Sponsors

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Maintenance & Mods (L322) > Range Rover L322 - Stuck in Extended or Off Road Height

Page 1 of 5

Print this entire topic ·

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Range Rover L322 - Stuck in Extended or Off Road Height

I just thought I would share a small problem I had with my Range yesterday. It may be one for the WIKI.

With everything working fine and crawling along the M25 I suddenly got a bong and a Suspension Fault. Lights on centre console out and the warning not to exceed 30 mph.

On getting home I tested the suspension and found that it would not adjust but just kept bouncing up to the fully extended (super extended) height with the message: Please reset when object has been removed etc - it thought I was stuck on a rock or similar!

Using Hawkeye I was able to reset the suspension and clear faults but the same issue re-occured immediatly.

The fault explained that the System could not vent and thus was stuck in the highest setting with no way of going down.

With a bit of searching I founds that the Compressor has a brass coloured cone shaped exhaust muffler/filter (sintered brass filter) near the top at the front of the car end of the compressor (Take the black metal cover off with four bolts after removing spare tyre). Apparently this is gets blocked over time as it is a hard sponge type filter.

My dirty cone filter clogged with desiccant:

The fix is to remove this filter using a 13mm spanner (Its shaped into a nut head at the top) get back in the car and start up and then select normal suspension setting. The system will let out a gasp as the compressed air is released and the car will drop to normal. The code can now be cleared and all will be well.

The car can be used without the filter (bit noisier) but this is probably not sensible in the long term. Ideally a replacement needs to be sourced but I think these are only available as part of a service kit.

Another option is to drill a tiny hole through the cone filter through the middle to allow air to escape but very little chance of anything nasty getting in. The Cone filter can then be refitted and all is good.

Tiny hole drilled through from thread end of cone:

I believe there is a service kit with a new filter cone (sintered brass filter), but I strongly recommend also replacing the dryer at the same time, as its desiccant is what causes the muffler to clog in the first place.

I think these "9mm Thread Sintered Brass Pneumatic Filter Noise Silencer Muffler" will fit: http://www.sourcingmap.com/pcs-9mm-thread-...tAodnDIAsw

http://www.amazon.co.uk/Thread-Sintered-Pn...B008ASX7P4

Last edited by Gazellio @ Prestige Cars on 16th Jan 2014 11:03am. Edited 9 times in total

16th Jan 2014 8:24am

RRUK
Site Supporter

Member Since: 08 Jun 2007
Location: UK
Posts: 6366

2019 Range Rover Vogue SE SDV8 Santorini Black

Great little fix that Gaz, and easy enough for anyone to do.

Let's Wiki this Stan. Discovery 4 HSE
1998 110 TUM HS FFR Hard Top XD WOLF
1982 Series 3 Hard Top

*Gone:L462 D5 HSE LUX, L663 Defender 110 HSE, Discovery 3 HSE, 2014MY Range Rover Sport 5.0 Supercharged AB Dynamic; L405 Exec Vogue SE 4.4, 5.0 Supercharged Autobiography, Defender TDCi XS CSW, Defender TD5 HT, Vogue SE TDV8, Vogue TD6, RRSport SC 4.2V8, Classic 3.9 Vogue Auto, Land Rover Series 3 SWB

16th Jan 2014 8:30am

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Yes Adam really is a 15 minute fix that a Dealer would probably charge hours for (as they probably would not know what to do) and end up replacing all the height sensors first

16th Jan 2014 8:32am

stan
Site Moderator

Member Since: 13 Jul 2010
Location: a moderate moderated moderator moderating moderately in moderation
Posts: 35264

its a known fault,

http://www.fullfatrr.com/forum/topic5724.h...air+filter

Click image to enlarge

16th Jan 2014 8:58am

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Yes Stan but that post is not exactly a WIKI fix is it....

16th Jan 2014 9:05am

nicedayforit

Member Since: 11 Jun 2011
Location: Beside the Solway
Posts: 3971

2004 Range Rover Vogue Td6 Giverny Green

Just need to know the thread size and one of these should work ok.

http://www.ebay.co.uk/sch/items/?_nkw=sint...4049132526

16th Jan 2014 9:17am

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Yes I think the thread is 9mm I added this to the thread a little while back:

Quote:
I think these "9mm Thread Sintered Brass Pneumatic Filter Noise Silencer Muffler" will fit:

http://www.sourcingmap.com/pcs-9mm-thread-...tAodnDIAsw

http://www.amazon.co.uk/Thread-Sintered-Pn...B008ASX7P4

I have ordered from Amazon...

16th Jan 2014 9:24am

nicedayforit

Member Since: 11 Jun 2011
Location: Beside the Solway
Posts: 3971

Never noticed your Edit
I've also ordered some as definitely worth changing as a service item.

16th Jan 2014 9:34am

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Yes my thoughts exactly even though the drilled one is working perfectly!

16th Jan 2014 9:49am

TugRR

Member Since: 11 Jan 2011
Location: Bakewell
Posts: 1199

Perhaps worth mentioning the model year / pump type, Gary - I understand there was a change at 06 MY ?
Good info !

Where do you go after one of these . . . ?

16th Jan 2014 11:00am

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

Sorry yes this was 200MY Vogue SE Supercharged - I will add to post above

16th Jan 2014 11:02am

jak480

Member Since: 06 Dec 2013
Location: Degernes
Posts: 44

2003 Range Rover Vogue Td6 Zambezi Silver

Hi
Just a tip you can buy these filters at any respectable pneumatic shop ( where they sell compressors,pneumatic valves,...) as they are very common used in pneumatic equipments
You can also clean them in petrol or with brake cleaner and then use a compressor to blow them dry.
Just a tip.

16th Jan 2014 12:09pm

Gazellio @ Prestige Cars

Member Since: 22 Jan 2010
Location: Chilterns, UK
Posts: 11309

16th Jan 2014 12:30pm

TugRR

Member Since: 11 Jan 2011
Location: Bakewell
Posts: 1199

. . . I'm going to check mine now you've mentioned it, Gary.
It looks like another item that should be on the service schedule . . .

Where do you go after one of these . . . ?

16th Jan 2014 1:32pm

jak480

Member Since: 06 Dec 2013
Location: Degernes
Posts: 44

Something to think about As there is normally only "clean" air coming out of the system where is the dirt that bloks the filter coming from??
Could it be a indication for something else that is about to fail in the circuit ?
Or is it simply dirty air that is being sukt in ?
Just a thought.

16th Jan 2014 1:51pm

Page 1 of 5

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum