fullfatrr.com - View topic - FBH relay question

Advertise on fullfatrr.com »

Forum · Gallery · Wiki · Shop · Sponsors

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Technical (L322) > FBH relay question

Page 1 of 1

Print this entire topic ·

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

FBH relay question

2002 model TD6 Vogue - FBH not working so had it out stripped cleaned and it looked in good condition. glow plug working etc. i have it on a remote so the fan starts, pump starts fans in the car etc as i have aux heating on the display. no fuel . looking at rave there is fuse 59 and it also mentions 69, will check 69 in a moment but no mention of a relay?

I also presume i can open the fuel tank access and get to the pump from there, anyone done this?

31st Jan 2015 9:02am

nicedayforit

Member Since: 11 Jun 2011
Location: Beside the Solway
Posts: 3966

2004 Range Rover Vogue Td6 Giverny Green

No relay involved.
These are the wiring diagrams. Sorry about the quality, it's the system.
If you require the wiring diagrams pm me.

Click image to enlarge

31st Jan 2015 11:07am

sasdiscos

Member Since: 16 Oct 2014
Location: Northants
Posts: 286

2010 Range Rover Vogue SE TDV8 Zambezi Silver

I thought it was permeant live, and then w bus for the control.

Steve You remind me of a young me, not much younger mind, perhaps even a little older!

31st Jan 2015 11:08am

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

Found it in rave to thank you for posting. I think.I either have a ecu board problem on the fbh as it also suffers with fan being on when you.open doors etc or a pump or a connection . will see if I can access the pump and.test for power etc this afternoon

31st Jan 2015 12:29pm

PaulB

Member Since: 17 Jul 2011
Location: Hampton
Posts: 877

2017 Range Rover Autobiography SDV8 Loire Blue

http://www.fullfatrr.com/forum/topic23111.html?highlight=paulb

31st Jan 2015 1:32pm

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

Thanks for the responses and links will get in touch with mike

31st Jan 2015 8:37pm

alanm_3

Member Since: 19 Feb 2011
Location: my House, unless Iâ€™m not at home, in which case Iâ€™m somewhere else.
Posts: 6712

Doh, sorry, misread FBH for FSR Got - 2017 SDV8 Autobiography in Loire Blue
Had- 2008 TDV8 Vogue SE in Java black
Had - 2007 S/C in Stornoway Grey

31st Jan 2015 8:46pm

ironhorse

Member Since: 13 Dec 2013
Location: birmingham
Posts: 355

2003 Range Rover Vogue 4.4 V8 Giverny Green

FBH fuel pump is not in the tank,its on a rubber bracket above and to the front of the tank

when the heater starts up it should run for about 28 seconds, die down a bit then after about another 5 seconds you should hear the fuel pump start to tick if this happens the heater part of it is fine, it stands a chance you have a fuel blockage

i have came across 2 in the last week with the fuel pipe into the burner blocked solid with carbon= but it needs open heart surgery to clean it out and a welder to put it back together
burner housing

cut the 3 welds off with a dremmal

part you should end up with after cutting welds off

remove cir clip that holds metal gauze and felt gauze underneath

carbon blocking fuel delivery hole

hole aftre clean up

new gauze fitted £22 off ebay (picture did not come out)
3 tack welds holding it back together

otherwise if it behaves differentaly

IF stop after 3 sec, restart 4 seconds later and finally stop at 2 minutes 7 sec;
An error is generated; may be caused by:

-Battery voltage lower than 10 volts
-Glow plug open or short circuit
-Circulation pump open or short circuit
-Fuel pump open
-PCB defective

IF a weird turbine noise appears at a door opening e.g.,PCB likely faulty.

IF stop after more than 2 minutes 10 sec, then
PCB and all devices are good (except doubtful glow plug)

IF stop at 4 minutes 5 sec, Glow plug resistor too high (0,6 ohms for instance),

IF stop at 4 minutes 40 sec it is a ignition fault, (fuel pump priming fault e.g.) = blockage in burner

http://www.the75andztclub.co.uk/forum/showthread.php?t=100297

31st Jan 2015 9:28pm

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

ta for info again. got the pump out . was just a mass of rust . tried on a 12v source and just click nothing tested connector and I have power . New pump ordered. I am still suspecting pub but will change this first

8th Feb 2015 6:19pm

ironhorse

Member Since: 13 Dec 2013
Location: birmingham
Posts: 355

the pump does just click once when you power it up
you need to keep on/off on/off on/off with the power to see if it draws any fuel through it

8th Feb 2015 7:04pm

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

if that is the case then it maybe ok apart from one end of the metal pipe just broke off.

I did expect it to just tick away as the voltage on my meter stayed around 10:30 to 11v when i connected to the fuel pump connector on the car( not the best connection) so it didn't pulse . when i pressed the remote i could hear the fan start, water pump and then the glow plug as that took some volts and slowed the fan for a moment. I will attempt to blow the pipes through before i fit the new pump.

After that it will be the blockage you mentioned above or and the PCB board.

I will do some photos too as forgot today

8th Feb 2015 9:14pm

mbmarkyb

Member Since: 18 Jan 2015
Location: basingstoke
Posts: 22

saw a few like this and still working

8th Feb 2015 9:19pm

Page 1 of 1

All times are GMT + 1 Hour

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum