Advertise on fullfatrr.com »

Home > Maintenance & Mods (L322) > Bonnet release cable HOW TO!!!
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Rockyd31



Member Since: 17 Dec 2016
Location: Chesterfield
Posts: 36
United Kingdom 2005 Range Rover Supercharged 4.2 SC V8 Java Black
Bonnet release cable HOW TO!!!

Ok so as the title suggests, I though I'd pen a "how to" for anyone contemplating wether or not to attempt this simple fix...

By all accounts it's a common problem. The part required cost me just Ł12 from Dan and took me 45 minutes with the use of a large chisel, posidrive screwdriver and a medium sized hex drive.

First, remove floor trim panel by pulling straight up sharply, I used a large chisel wrapped in masking tape to help get purchase

Click image to enlarge


Next, was to remove the trim surrounding the bonnet release lever at the RH side of the drivers footwell by pulling toward the rear of the vehicle
Click image to enlarge


Now you should be able to see the break in the cable as in the image
Click image to enlarge


Grab the broken cable with pliers or similar and pull to release the bonnet (if needed you may have to trim the sheath to get purchase on the cable)
Click image to enlarge


Once under the bonnet you need to split the 2 halves of the cable by firstly locating the join above the drivers front wheel
Click image to enlarge


The carrier is attached to the inner wing with 2 clips and comes away easily
Click image to enlarge


Then simply open the carrier with a flat blade screwdriver to separate the 2 halves
Click image to enlarge


Lastly pull the old cable through from the drivers footwell grabbing the rubber grommet which seals the hole in the fire wall and remove the 3 hex screws to detach the bracket from the car
Click image to enlarge


Here you can see the difference between the old and new cable
Click image to enlarge


Fitting the new cable is reverse of the previous steps, thread the new cable from the drivers footwell
Click image to enlarge


Please note the need to seat both the end of the cable and the metal collar correctly within the carrier
Click image to enlarge


Replace the carrier


At this stage grab a brew to reduce the risk of turning the air purple as you seat the rubber grommet back into the firewall then procedure to use washing up liquid and a thin screwdriver to your advantage.

Then attach the bracket and handle and replace the black trim next to the peddle box, noting the 2 locating clips as you push it back into place.
Click image to enlarge


Finally pop the floor trim back down, noting that the clips slide up and down the rail so you may need to manipulate them before you push it into place. Clearly if you have my OCD you will hoover all the crumbs up first Embarassed


JOB DONE, BOSHHHH Thumbs Up

Last edited by Rockyd31 on 7th May 2017 4:38pm. Edited 1 time in total
Post #437362 7th May 2017 4:27pm
View user's profile Send private message View poster's gallery Reply with quote
Weegie



Member Since: 09 Jun 2014
Location: East Sussex
Posts: 3235
Scotland 2008 Range Rover Vogue TDV8 Stornoway Grey

Nice write up Thumbs Up

I found it useful to attach a thin cord to the under bonnet end of the broken cable before pulling it through. It made threading the new cable back through the bulkhead simpler. John
2008 Stornoway Grey 3.6 Tdv8 Vogue
2005 TD6 Java Black Vogue - Written off!!
GAP iiD BT
2003 Discovery TD5 Auto, Nanocom Evolution - gone to a new home!
MasseyFerguson 152 - No electronics!! - Sold
Post #437363 7th May 2017 4:31pm
View user's profile Send private message View poster's gallery Reply with quote
Rockyd31



Member Since: 17 Dec 2016
Location: Chesterfield
Posts: 36
United Kingdom 2005 Range Rover Supercharged 4.2 SC V8 Java Black

Good point Weegie but with my tiny hands it wasn't required Laughing Lee

XR2i (1.6)
Peugeot 306 (1.4l)
Vauxhall Cavallier CDX (2.5 V6)
Renault Laguna (1.9D)
Vauxhall Vectra GSI (2.5 V6)
Mitsubishi GTO (3.0 twin turbo)😬
Porsche Boxter S (3.2 straight 6)
BMW 535D
VW Polo 1.4S (its all about the S)
BMW 330CI
FFRR Supercharged
Post #437368 7th May 2017 4:44pm
View user's profile Send private message View poster's gallery Reply with quote
Alex Millar



Member Since: 05 Jun 2015
Location: Glasgow and Arran
Posts: 24
United Kingdom 2003 Range Rover Vogue 4.4 V8 Adriatic Blue

Many thanks for the great write up and photos to show how to do this as I was at a loss how to even open the bonnet before I read this.
Post #470289 27th Feb 2018 7:43pm
View user's profile Send private message View poster's gallery Reply with quote
lounge_on_wheels



Member Since: 10 Dec 2016
Location: in the great land of oz
Posts: 269
Australia 2003 Range Rover HSE Td6 Zambezi Silver

May I add an important tip.

Put a bonnet ( hood ) prop AKA stick under the bonnet. I had wind blow my bonnet shut, Whilst I was threading the new cable in the footwell locking it, It locked the bonnet and took a bit of work to open it again.
Post #471620 8th Mar 2018 9:59am
View user's profile Send private message View poster's gallery Reply with quote
Alex Millar



Member Since: 05 Jun 2015
Location: Glasgow and Arran
Posts: 24
United Kingdom 2003 Range Rover Vogue 4.4 V8 Adriatic Blue

Thanks for that. I'll keep that in mind as still to renew the cable due to delays supplying the part.
Post #471711 8th Mar 2018 8:17pm
View user's profile Send private message View poster's gallery Reply with quote
Happy Eater



Member Since: 05 Dec 2017
Location: Maidstone
Posts: 7
United Kingdom 

Thanks for this - took about 15 mins to do following this guide...and the cable was only 14GBP from local dealers!
Post #500468 3rd Jan 2019 8:44pm
View user's profile Send private message View poster's gallery Reply with quote
Joe90



Member Since: 29 Apr 2010
Location: Hampshire
Posts: 6409
England 

nothing like a "trimmed sheath" Thumbs Up .
Experience is the only genuine knowledge, but as time passes, I have forgotten more than I can remember Wink
Volvo V70 P2 2006 2.4 Petrol 170bhp Estate SE
MG Midget Mk1 1962

Previous: L322 Range Rover TDV8 3.6 2008; L322 Range Rover TD6 3.0 2002; P38A Range Rover V8 1999
Post #500481 3rd Jan 2019 11:14pm
View user's profile Send private message View poster's gallery Reply with quote
mazza7282



Member Since: 10 May 2020
Location: Essex
Posts: 99
United Kingdom 2003 Range Rover SE Td6 Adriatic Blue

Great write up - Mine snapped earlier on today !
As already suggested - part was ÂŁ14.99 from Land Rover (not local Sad). Still, beats waiting for the part to turn up off the net !
Post #570756 23rd Oct 2020 5:01pm
View user's profile Send private message View poster's gallery Reply with quote
bigbo



Member Since: 07 Jul 2014
Location: Derbyshire
Posts: 583
United Kingdom 2006 Range Rover Supercharged 4.2 SC V8 Buckingham Blue

2 questions

What guides the cable back up to above the inner wing, does it run through a tube of some sorts?

Should this be a regular maintenance item, it seems that it is a common fault or was the design changed at anytime to prevent failure?

Thanks
David Range Rover 4.2 Supercharged 2006
Ford Focus EcoBoost 1.5 2017
MG TF 2003

Previous Cars of note
Land Rover Discovery 2
Jaguar Mk2 3.8 - Company car
MG Midget 1974 - Concours
Post #570762 23rd Oct 2020 6:02pm
View user's profile Send private message View poster's gallery Reply with quote
mazza7282



Member Since: 10 May 2020
Location: Essex
Posts: 99
United Kingdom 2003 Range Rover SE Td6 Adriatic Blue

I just poked the cable & sheeth through the hole, as was already mentioned a little bit of swearing to the rubber grommet to fit through the hole. Then once it was situated properly I put my hand down to grab the cable and ran it along the same path as it was before. Mine looked like it was fed through a rather dodgy route so I made sure it went through the same route but was free of any foreign objects such as rigid brake pipes, brake booster vaccum hose etc.

I see your thinking in relation to a maintenance item, but even with the cable snapping where it does. It can still be opened with the pair of plyers pulling at the cables. i'd just replace it when it breaks tbh.

My L322 has done 186.000 miles on a 2003. so think that's long enough Smile
Post #571406 31st Oct 2020 3:17pm
View user's profile Send private message View poster's gallery Reply with quote
Paul K



Member Since: 11 Jan 2019
Location: Eastern Oregon
Posts: 13
United States 

Just did this on my North American Spec (LHD) 2007 SC. One extra step required;

-You need to pry the cover off the foot rest. It comes up on the drivers side first. Once that’s removed, you’ll see a 10mm nut under it that needs to be removed. Then you can pull off the cover that surrounds the bonnet release lever.

Great write up, thanks! 2007 Supercharged.
Post #577308 27th Dec 2020 1:08am
View user's profile Send private message View poster's gallery Reply with quote
Danwilderspin



Member Since: 15 Jun 2016
Location: Cambridgeshire
Posts: 2215
United Kingdom 2007 Range Rover Vogue SE 4.2 SC V8 Zermatt Silver

Hi all thanks for this mine snapped and I replaced it all went ok but when I pull the handle it doesn’t snap back down like before it stays slightly up and I have to push it down - any ideas?

 Current stable:
2006 BMW M6
2007 4.2 V8 S/C FF
Gone:
2002 4.4 V8 FF
Post #586093 3rd Mar 2021 6:48pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
<  Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
fullfatrr.com RSS Feed - All Forums


Switch to Mobile site