fullfatrr.com - View topic - EGR valve replacement L322 TDV8 3.6

Advertise on fullfatrr.com »

Forum · Gallery · Wiki · Shop · Sponsors

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Technical (L322) > EGR valve replacement L322 TDV8 3.6

Page 1 of 3

Print this entire topic ·

Edfors

Member Since: 26 Oct 2012
Location: Uppsala
Posts: 168

2008 Range Rover Vogue TDV8 Alaska White

EGR valve replacement L322 TDV8 3.6

EGR Valve assemblies of a TDV8.

Click image to enlarge

Beware this is a very image intensive post, 100+ images and steps to replace both EGR valves on a 3.6 TDV8. I also chosen to replaced a few inlet hoses and a couple of O-rings, I think this is worthwhile when you already have to release these for access.

Reason for change was that it had got into fault mode and displayed "Engine systems fault" on our last weekend laning trip. The message went away and all appeared normal after restart, but it came up four times during the weekend so I thought it would be better to be safe than sorry and decided to replace both EGR's. When getting in there I noticed that someone had been there before, the left hand side EGR seems to have been replaced once earlier. I don't yet have a fault code reader and could not decide which EGR was failing but think it's worth to replace both EGR's while you're down there, same with the inlet hoses.

WARNING: There is really limited space and you may lose nuts/bolts/tools downwards, so removing the under tray first could be a good idea, I lost one 10 mm ring spanner, which was caught on the under tray and retrieved afterwards. There is also a fair amount of electrical connectors to release and re-fit, if you not comfortable with these or opening up the coolant hoses please consider using a specialist for the job. Also there are potential risks of severe engine damage if you drop anything into the open inlet pipes. Keep things clean and don't risk your engine.

To complete the following job you need these parts:
1 x LR018322, EGR Valve Left Hand 3.6l V8 L322 Range Rover + Sport
1 x LR018321, EGR Valve Right Hand 3.6l V8 L322 Range Rover + Sport
2 x LR004250, EGR Tube>EGR Gasket 3.6 V8 - L322 Range Rover + Sport
2 x LR003828, EGR Valve>Tube Gasket 3.6 Dsl
2 x LR003831, EGR Valve Gasket 3.6l V8 Diesel

Optional parts:
2 x LR004076, Duct - Air Inlet Manifold 3.6l V8 Lion Diesel - Range Rover Sport + L322
2 x LR014468, Intake Manifold Air Duct Hose - 3.6l V8 Diesel - Range Rover L322 + Sport
1 x PNH500500, Rad Hose Upper + Clips LH 3.6 G-CAT
1 x PNH500510, Rad Hose Upper + Clips RH 3.6 G-CAT
2 x LR003898, O Ring EGR Valve Tube 3.6L DSL G-CAT

Tools used:
13 mm ring spanner
10 mm ring spanner and sockets (ratcheting ring spanners helps)
8 mm ring spanner and sockets (ratcheting ring spanners helps)
Torx 30 socket (mine was 3/8")
1/4" wobbly extensions of different lengths
1/4" universal joint
1/4" ratchet handle
3/8" extension
3/8" ratchet handle
Torque settings between 10 and 25 Nm for reassembly.
Hose clamp (to close water hose)
Pliers for hose clips
A plastic pry tool for connector studs and to loosen stuck hoses.
A couple of tie clips for tie up the coolant pipes out of the way.

Difficulty of job, 3 of 5. Time used, I did it over 4 evenings, maybe 1- 2 hours each evening.

Click image to enlarge

Open the hood in service mode, open the small spring clips on the dampers with a small, thin flat screw driver.

Click image to enlarge

Do both sides while you support the hood with one hand, or use a assistent supporting this (recommended). Move it straigt up and fold out the locking bars over the small pegs each side.

Click image to enlarge

Remove the battery negative cable and put it aside so it cannot spring back and make contact with the terminal.

Click image to enlarge

Remove the engine cover by pulling it upwards.

Click image to enlarge

Lift off the hood seal.

Click image to enlarge

The small holes in my hood seal was facing the windshield.

Click image to enlarge

Undo the A/C support bracket.

Click image to enlarge

also from the A/C pipes and the bold on the other side as well.

Click image to enlarge

Then the plenum chamber is loose and can be pulled straigt out.

Click image to enlarge

Giving this view. You see the twin cooland pipes to release next.

Click image to enlarge

With two nuts and one bolt you can lift and bend the pipes up and I tied them up with a strips to be out of the way.

Click image to enlarge

Disconnect and release the wiring to EGR valves. Both sides.

Click image to enlarge

EGR connector to be opened and released.

Click image to enlarge

Follow the engine harness and remove where its tied down.

Click image to enlarge

Theres alot of wiring and a big bracket in the centre.

Click image to enlarge

Follow the branches of the wiring and release all clips and connectors.

Click image to enlarge

A plastic pry tool is good help releasing the tie down plugs.

Click image to enlarge

Some plugs are more challanging and this one had a sliding lock.

Click image to enlarge

The CPS in the back of the engine is in a very tight spot. Let it take it's time to figure out how to release them all.

Click image to enlarge

The CPS connector released bu putting a flat screwdriver behind the hatch and pulling.

Click image to enlarge

WIth all wires and connectors loose you can undo the engine cover mounting bracket.

Click image to enlarge

Then you can access and release the vacuum hoses.

Click image to enlarge

Just give them a pull and the vacuum hoses will release.

Click image to enlarge

On the outer side of each head there is a protective plate. Hold in with some easy and some hard to reach nuts.

Click image to enlarge

This is what it looks with the metal plate off.

Click image to enlarge

One of the plates off.

Click image to enlarge

With the plats off you can reach the injector connetors.

Click image to enlarge

Which all has to come off to be able to release the harness.

Click image to enlarge

Its very tight on the left side, even hard to see the small nuts deep down there.

Click image to enlarge

One of the top nuts removed and another down in the corner just visible.

Click image to enlarge

Another just about visible deep down.

Click image to enlarge

I attacked these nuts with 1/4" ratchet tools.

Click image to enlarge

And with several extensions. You can see the socked if you follow the line of the extension.

Click image to enlarge

Anther nut, from another "access hole".

Click image to enlarge

Be patient and they will all come off, and with a good pull you get the protective plates off.

Click image to enlarge

Follow the wiring back and release all tie downs.

Click image to enlarge

It was quite some grime in here, I put some protective cloth in the air openings and cleaned it up with compressed air. Thought this was the time, before opening any of the manifold or exhaust pipes.

Click image to enlarge

Next I unscrewed the EGR outlet tubes, 4 torx bolts.

Click image to enlarge

Loosen the clips of the rear manifold hoses, 4 clips.

Click image to enlarge

Repositioned the hoses towards the manifold.

Click image to enlarge

Unscrewed and released the hoses to the air cooler as well as the MAPT connectors.

Click image to enlarge

Release the clips on the 90* bent hoses.

Click image to enlarge

Unscrew the 6 bolts fastening the manifold.

Click image to enlarge

The manifold is now loose and ready to be lifted off, exept of 2 connectors.

Click image to enlarge

Which are connected to throttle body and can be released when it's lifted up a little bit.

Click image to enlarge

Now the intake manifold can be lifted off and put aside.

Click image to enlarge

When I lifted it off I saw this little fellow falling down on the engine.

Click image to enlarge

But I could soon see it was missing from one of the throttle body connectors.

Click image to enlarge

And could push it back to its home.

Click image to enlarge

Now we're almost half way through and finally you can see the actual EGR valve assemblies.

It's time to take a cup of tea and see where you have got to so far. Supporter and maintainer of EDF - Mrs Edfors' shopping cart.

Last edited by Edfors on 15th May 2017 5:49pm. Edited 2 times in total

29th Jun 2015 8:08pm

Dean

Member Since: 23 Mar 2014
Location: Glasgow
Posts: 51

Wow, brilliant write up. Keep going please. It is all very exciting. 2006 FFRR TDV8 Vogue
2012 Discovery 4 SDV6 GS

29th Jun 2015 8:51pm

northernmonkeyjones

Member Since: 24 Mar 2012
Location: derby
Posts: 8504

2016 Range Rover Autobiography SDV8 Santorini Black

thats awesome There is nothing that can't be fixed with a hammerðŸ˜œðŸ˜œ
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

29th Jun 2015 8:55pm

Edfors

Member Since: 26 Oct 2012
Location: Uppsala
Posts: 168

Thanks, here comes the second and last part.

Click image to enlarge

Removing the fuel rail support bracket. Two bolts on each bracket.

Click image to enlarge

Easy to lift off.

Click image to enlarge

Release the exhaust inlet pipe, two bolts, this is the upper.

Click image to enlarge

and socket on the lower.

Click image to enlarge

Release 4 bolts holdning the EGR assembly. Two seen here.

Click image to enlarge

Now the assembly is free, except water hoses.

Click image to enlarge

Clamps on both water pipes to the exhaust cooler. And loosen the hose clips.

Click image to enlarge

Pulling off the hoses. I did one side at the time, thus two clamps is enough and gives a minimal water loss.

Click image to enlarge

EGR assembly, release the exhaust cooler with torx bolts.

Click image to enlarge

Old and new EGR valve.

Click image to enlarge

New gasket on the EGR inlet pipe.

Click image to enlarge

EGR with new gasket towards the cooler, both ends and back for reassembly. 10 Nm on most bolts.

Click image to enlarge

Tightening it back down.

Click image to enlarge

And the fuel rail bracket back in place as well. This should be done with 23 Nm.

Click image to enlarge

Both EGR's replaced.

Click image to enlarge

With the EGR secured I replaced both air cooler hoses, both old and new in this photo.

Click image to enlarge

And then turned to the inlet manifold and replaced the four short air hoses.

Click image to enlarge

Undo the EGR pipes.

Click image to enlarge

In there you see a O-ring, remove this.

Click image to enlarge

Old O-ring was hard and full of soot.

Click image to enlarge

Place new O-ring on the EGR outlet pipe.

Click image to enlarge

Reassembly and fit new gasket on the EGR valve side.

Click image to enlarge

Double check the engine side and see all brakets and screws are back and lift the pipes and harness aside to make clear for putting bach the inlet manifold.

Click image to enlarge

Inlet manifold ready to go back.

Click image to enlarge

Be brave, put it back and tighten up all the screws.

Click image to enlarge

Don't forget any of the throttle connectors.

Click image to enlarge

And fit all the bolts.

Click image to enlarge

Contine with the harness, connectors and harness bracket.

Click image to enlarge

Don't forget the vacuum pipes.

Click image to enlarge

And the engine cover bracket.

Click image to enlarge

Reposition and tighten the inlet hoses.

Click image to enlarge

There are 6 of them.

Click image to enlarge

Including the front cooler one's. The genuine LR one's have all new hose clips already correct positioned on them.

Click image to enlarge

Put back all tie downs.

Click image to enlarge

It's loads of wires and cables, so pictures help getting it all back in the same positions, which goes over and under each other.

Click image to enlarge

Crank position is still down there, easier to connect first and then press in the tie downs.

Click image to enlarge

Continue with the injector and EGR connectors.

Click image to enlarge

These fuel pipes don't have to be opened, just pressed carefully at the side.

Click image to enlarge

Getting the side metal shields back in place and getting the nuts on there, be careful not loosen any, I put a small drop of grease on the socket to hold it on there while getting it onto the stud.

Click image to enlarge

It's possible to get them all back, bit it's very tight.

Click image to enlarge

And a good small torch helps, because it can be dark down there as well, you see two top nuts and the socket for a third deep down.

Click image to enlarge

Some brackets and hose fasteners to go back as well.

Click image to enlarge

With all connectors and the harness back on, it's time for the coolant hoses to go back down.

Click image to enlarge

And on the coolant hoses there is another cable fastened.

Click image to enlarge

The CPS cable goes here.

Click image to enlarge

All the nuts for the shields are now back.

Click image to enlarge

Remove the cloth from the plenum chamber openings.

Click image to enlarge

Putting the plenum chamber back.

Click image to enlarge

Tigheten it back with A/C bracket and install the rubber hood seal.

Click image to enlarge

Engine cover back, battery cable reconnected, always negative off first and on last. And return hood from service position.

Click image to enlarge

Ready to enjoy again

I didn't have anything to clear fault codes so I didn't do this, but would be a good idea if you have a diagnostic tool. Supporter and maintainer of EDF - Mrs Edfors' shopping cart.

29th Jun 2015 9:09pm

PaulB

Member Since: 17 Jul 2011
Location: Hampton
Posts: 877

2017 Range Rover Autobiography SDV8 Loire Blue

Great write up.

Thanks for taking the time.

29th Jun 2015 9:23pm

alanm_3

Member Since: 19 Feb 2011
Location: my House, unless Iâ€™m not at home, in which case Iâ€™m somewhere else.
Posts: 6723

You have no idea how much time this might save me in the not too distant future!

Well done that man! Got - 2017 SDV8 Autobiography in Loire Blue
Had- 2008 TDV8 Vogue SE in Java black
Had - 2007 S/C in Stornoway Grey

29th Jun 2015 9:36pm

SKOT

Member Since: 24 Oct 2012
Location: Milton Keynes
Posts: 792

2006 Range Rover Supercharged 4.2 SC V8 Bonatti Grey

Fascinating. Much respect to you

It's a shame that you didn't get many pictures though..... 2006 4.2 SC
2019 Renault Zoe Dynamique Nav

29th Jun 2015 9:39pm

Haylands

Member Since: 04 Mar 2014
Location: East Yorkshire
Posts: 8190

2014 Range Rover Autobiography SDV8 Loire Blue

Excellent write up, makes me wish I had a diesel just so I could change them..... Pete

__________________________________________________
2014 L405 Autobiography SDV8 4.4 Loire Blue Ebony interior
2011 L322 Vogue SE 4.4 TDV8 Baltic Blue. Parchment over Navy Interior. Sold
2012 L322 Autobiography 5.0 Supercharged Ipanema Sand, Jet Interior. Sold
2002 L322 Vogue 4.4 V8 Epson Green, Ivory over Aspen Interior (Fatty Offroader) Sold
-Click for Project Fatty off roader-

29th Jun 2015 10:32pm

stan
Site Moderator

Member Since: 13 Jul 2010
Location: a moderate moderated moderator moderating moderately in moderation
Posts: 35269

excellent..

i have entered your 'how to' in the great depository of knowledge called the wiki.. ... - .- -.

Y. O. L. O.
.

30th Jun 2015 6:29am

Mr Tee

Member Since: 13 Dec 2010
Location: Near Wackyjim
Posts: 2641

Wow, incredible write up, you have just confirmed why a good Indy is crucial for us more mechanically challenged members !

30th Jun 2015 6:59am

mjdronfield

Member Since: 04 Nov 2011
Location: Derbyshire
Posts: 7793

2011 Range Rover Vogue SE TDV8 Buckingham Blue

And I was thinking that if I got a tdv8 I could just replace them with a blanking kit and have them mapped out.

2011 Range Rover Vogue SE 4.4 TDV8

Previous cars :
2003 Range Rover Vogue TD6
1999 Discovery Td5 ES
1995 BMW M5 3.8 6 speed
1992 Range Rover 3.9 Efi Vogue
1992 BMW M5 3.8
1988 BMW 735i SE
1989 Ford Sierra XR4x4 2.9i
1981 Ford Fiesta Supersport

30th Jun 2015 4:29pm

dhallworth

Member Since: 10 Oct 2011
Location: Glasgow
Posts: 3068

2012 Range Rover Autobiography TDV8 Baltic Blue

What a cracking write up. must have taken almost as long to take and sort the pictures out as it did to do the job.

I've been told by a friend of mine in Scarborough who runs a TDV8 Sport that you can map them out without blanking them as long as they've not failed before you map them out as they'll default to the closed position. Not sure if he's right or wrong though.

I'm still glad I've got a petrol and don't have these to worry about though!

David. 2002 4.6 Vogue SE - Alveston Red with Lightstone Leather
2007 Range Rover Supercharged in Java Black with Ivory Leather
2012 Range Rover 5.0 SC Autobiography in Indus Silver with Jet/Ivory Interior
2012 Range Rover 4.4 TDV8 Autobiography in Baltic Blue with Sand Interior

31st Mar 2016 8:19am

Scottyav

Member Since: 11 Feb 2013
Location: Cannock Staffordshire
Posts: 1204

2007 Range Rover Autobiography TDV8 Zambezi Silver

Or have them mapped out like me just last week loads better more responsive and NO worries of them getting blocked and f*****g the turbo/engine _____________________________________________________
Zambezi silver Vogue Se unique

31st Mar 2016 11:50am

PaulB

Member Since: 17 Jul 2011
Location: Hampton
Posts: 877

Who did it Scott?

Pete Bell?

31st Mar 2016 12:05pm

Scottyav

Member Since: 11 Feb 2013
Location: Cannock Staffordshire
Posts: 1204

theres a firm in droitwich and they do a few pretty good tbh for £ 150 _____________________________________________________
Zambezi silver Vogue Se unique

1st Apr 2016 9:10am

Page 1 of 3

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum