i've spent some time sorting out the wiki so its easier to use and find stuff...have a look and let me know if there are any problems or bits that need tweaking..


stan ... - .- -.




Y. O. L. O.
.

Looking great on the wiki  .
Experience is the only genuine knowledge, but as time passes, I have forgotten more than I can remember
Volvo V70 P2 2006 2.4 Petrol 170bhp Estate SE
MG Midget Mk1 1962

Previous: L322 Range Rover TDV8 3.6 2008; L322 Range Rover TD6 3.0 2002; P38A Range Rover V8 1999

 ... - .- -.




Y. O. L. O.
.

Much much better....

I noticed the Key Fob Programming routine (Key in turn turn ign. onn/off quickly Hold Unlock while pressing lock three times then release unlock heat unlock/sound then other key then key in on/off etc) is not there?

cant remember seeing that key fob how to , do you want to add it into the wiki gary? ... - .- -.




Y. O. L. O.
.

Going out but:

Key in turn turn ign. onn/off quickly

Hold Unlock while pressing lock three times then release unlock button

Hear unlock/sound

Then within a few seconds repeat with other key

Listen for unlock/sound

Then within a few seconds key in ign. and on/off quickly

Job done

found this by dan,


Initialization Procedure

*Ensure the vehicle is unlocked and the driver and front passenger doors are closed.

*Install a key/remote handset in the ignition switch, then turn the ignition switch to position I and back to position 0 in less than 5 seconds to put the GEM into the initialization mode. Continue the procedure within 30 seconds of turning the ignition switch to position 0.

*Remove the key/remote handset from the ignition switch.

*Press and hold the unlock button for a maximum of 15 seconds. During this time, momentarily press the lock button three times within 10 seconds.

*Release both buttons.

*Successful initialization is indicated by the GEM locking then unlocking the vehicle. If this does not occur, repeat step D.

*Repeat steps D. and E. with all other remote handsets belonging to the vehicle (4 maximum). Begin the
initialization of each remote handset within 30 seconds of completing the previous initialization, or the GEM will
drop out of the initialization mode and the complete procedure will have to be started again.


is this the same thing? ... - .- -.




Y. O. L. O.
.

Perfect but it need a finanal section:

YOU need to put the key back in the ignition and turn on/off to finish the procedure!

Initialization Procedure

*Ensure the vehicle is unlocked and the driver and front passenger doors are closed.

*Install a key/remote handset in the ignition switch, then turn the ignition switch to position I and back to position 0 in less than 5 seconds to put the GEM into the initialization mode. Continue the procedure within 30 seconds of turning the ignition switch to position 0.

*Remove the key/remote handset from the ignition switch.

*Press and hold the unlock button for a maximum of 15 seconds. During this time, momentarily press the lock button three times within 10 seconds.

*Release both buttons.

*Successful initialization is indicated by the GEM locking then unlocking the vehicle. If this does not occur, repeat step D.

*Repeat steps D. and E. with all other remote handsets belonging to the vehicle (4 maximum). Begin the
initialization of each remote handset within 30 seconds of completing the previous initialization, or the GEM will
drop out of the initialization mode and the complete procedure will have to be started again.

*When all handsets reprogrammed quickly put key back in ignition switch and turn to 1 and back to 0 to finalise procedure.

Gary

gary, i cant remember seeing the 'lubricating gear linkage' tip that you posted being on the wiki ,so maybe include that when you do the key fob tip... ... - .- -.




Y. O. L. O.
.

scarey wrote:

gary, i cant remember seeing the 'lubricating gear linkage' tip that you posted being on the wiki ,so maybe include that when you do the key fob tip...

you're right, hidden in the common problems bit.... ... - .- -.




Y. O. L. O.
.