fullfatrr.com - View topic - Starter motor replacement L322 TDV8

Advertise on fullfatrr.com »

Forum · Gallery · Wiki · Shop · Sponsors

Home · FAQ · New Posts · My Posts · PMs · Search · Members · Map · Calendar · Profile · Donate · Register · Log In

Home > Technical (L322) > Starter motor replacement L322 TDV8

Page 1 of 9

Print this entire topic ·

Edfors

Member Since: 26 Oct 2012
Location: Uppsala
Posts: 168

2008 Range Rover Vogue TDV8 Alaska White

Starter motor replacement L322 TDV8

The starter on our 2008 TDV8 gave up and just had the 'click'. So I ordered a new starter, part no LR032541. There is a surcharge, so it may be worth sending the old one back.

Difficulty of job, 2 of 5. Time including tea breaks around 3 hours first time.

Tools required. 8 and 10 mm 1/4 sockets with ratchet. 13 mm sockets with 3/8 or 1/2 ratchet and a 17 mm combination spanner. 22 mm for wheel nuts, jack to raising the vechile and support for the raised vehicle.

Click image to enlarge

First, check battery is ok. I did this with jump leads and a known good battery. Starter would still not go.

Loosen but don't remove wheel nuts on front right wheel. Then raise and support vehicle, you will need to get access from below at the right hand side.

Remove FR hand wheel, UK drivers side.

Remove battery negative cable from battery, just bend and put cable aside so it cannot get back and touch the battery connector.

Next remove the engine under shield, just 6 small 10 mm screws.

Click image to enlarge

Next is a heat shield in the rear side of FR wheelarch. Two nuts from the wheel side and two screws from below.

Click image to enlarge

Now you can see the starter with another heat shield on top of it.

Click image to enlarge

Another three 10 mm screws to remove.

Click image to enlarge

Wiggle out the heatshield and you see this.

Click image to enlarge

At the front end of starter you find two plastic caps. Remove the large, can be prised out with a small flat screwdriver. And just pull of the small one which has a cable attached.

Click image to enlarge

With caps off, you can now remove the cable to the solenoid, 8 mm socket.

Click image to enlarge

Use the 17 mm spanner to remove large nut and loosen cable. (NB! Battery cable must be disconnected before touching these cables with a tool!)

Loosen two big screws in the back end of the starter and wiggle it all out. It goes out through the wheelarch, but takes some twisting.

Click image to enlarge

New and old starter.

Click image to enlarge

When you get this far, it's fairly easy to reverse the procedures. In with the new and here I have connected a couple of breather hoses to it as well. Fasten the two rear big bolts, these should be tight.

Click image to enlarge

Reconnect the connectors and put back the caps. I wire brushed the cable connectors first. And pay attention to the location tab to get this into the right position before tightening.

Click image to enlarge

Reinstall heat shield.

Click image to enlarge

Reinstall next heatshield.

Reinstall undertray, wheel and last the battery negative cable. Some small spark may occur when you do this.

Started at first attempt!

Supporter and maintainer of EDF - Mrs Edfors' shopping cart.

19th May 2015 8:29pm

northernmonkeyjones

Member Since: 24 Mar 2012
Location: derby
Posts: 8497

2016 Range Rover Autobiography SDV8 Santorini Black

Nice job👍👍

One for the wiki Stan! There is nothing that can't be fixed with a hammer😜😜
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

19th May 2015 8:34pm

stan
Site Moderator

Member Since: 13 Jul 2010
Location: a moderate moderated moderator moderating moderately in moderation
Posts: 35245

nice job Patrik, wiki'fied.. ... - .- -.

Y. O. L. O.
.

19th May 2015 8:52pm

RRD

Member Since: 19 Mar 2014
Location: Antwerp
Posts: 40

2012 Range Rover Vogue TDV8 Santorini Black

Hi guys,

bumping an old thread here!

The starter motor on my 4.4 TDv8 went dead and it seems to be the same starter motor as used on the 3.6 TDv8.
Is the procedure of replacement the same too? Or can I expect differences? '17 Range Rover 5.0 Supercharged AB (Sold)
'16 Range Rover SDv8 AB (Sold)
'15 Range Rover SDv8 Vogue (Sold)
'13 Range Rover SDv8 Vogue (Sold)
'12 Range Rover TDv8 (Sold)
'10 Range Rover 5.0 Supercharged
'03 BMW E39 M5
'01 BMW E46 M3

27th Feb 2019 2:43pm

Shaun

Member Since: 02 Jul 2010
Location: Hull
Posts: 58

2011 Range Rover Vogue 4.4 V8 Orkney Grey

I've not changed one on a 3.6, but have on a 4.4. Was told that there is less room and I would have to disconnect the anti roll bar. Managed to do it without disconnecting, but very tight.
A post mortem revealed burnt solenoid contacts. I did measure the voltage at the solenoid when trying to start and only had 9.5V. I believe the cable to the solenoid is in 4 pieces, 2 X 4.0mm & 2 X 2.5mm. I either had a bad connection somewhere or Land rover got their sums wrong when designing the start system!! Anyway, now replaced with a larger cable straight through and no more starting problems.

2004 TD6 - Gone
2011 4.4 TDV8

1st Mar 2019 11:38am

Baltic Blue

Member Since: 13 Aug 2015
Location: North Wales
Posts: 3758

2011 Range Rover Vogue SE TDV8 Baltic Blue

Thanks for the 4.4 info Shaun.
Did the cable come out in 1 piece? or 4 separate bits?
Please can you add any further details of the new cable you fitted.
I presume you replaced it in one continuous lead with no joints?

Click image to enlarge

Mike. G reg 2.5VM Vogue Portofino red 1991- 1999
V reg 2.5td P38 Rioja red 1999- 2006
53 reg td6 Vogue Oslo blue 2006- 2015
11 reg 4.4 TdV8 Vogue SE. Baltic blue 2015- date.
https://www.fullfatrr.com/forum/topic56162...tty+affair

1st Mar 2019 12:08pm

Shaun

Member Since: 02 Jul 2010
Location: Hull
Posts: 58

The cable I replaced was the smaller one from the start relay in the fuse box to the solenoid, too much of a volt drop on it. Spliced a new one in the fuse box near the relay and found a convenient run down to the starter. 2004 TD6 - Gone
2011 4.4 TDV8

1st Mar 2019 8:19pm

Tight777

Member Since: 26 Jan 2018
Location: Epping
Posts: 88

2007 Range Rover Vogue TDV8 Zermatt Silver

Just had to replace mine.
Just to add I couldn't get the starter out through the side to the wheel arch, mine came out through the bottom chassis rails.

24th Aug 2019 6:23am

dibber83

Member Since: 22 Sep 2012
Location: Taunton
Posts: 22

2012 Range Rover Autobiography TDV8 Stornoway Grey

Just done this on mine following this guide. Quite straight forward, only simple hand tools required plus a lot of patience trying to manoeuvre the motor through the chassis. Engine started instantly afterwards, which made me I realise I have had an issue for some time - sometimes when starting the car previously it would take a while to crank, sometimes it wouldn’t start without turning the ignition off and on, I initially thought it was delayed start waiting for glow plugs due to the cold weather. My dad borrowed the car a couple of weeks ago and said he struggled to start the car but I put that down to him being old and unfamiliar with the car

Anyway all good now hopefully. It took about 4 hours including twice having to go for more tools - a range of extensions and different length sockets of various sizes are needed to be able get to each nut. 2012 4.4TDV8 AB
———————————
2016 Mercedes C350e
2003 TD6 Vogue
2010 Alpina D3 BT
2005 Audi A4 2.0TDi SLine
1973 Series IIa
2001 BMW 320
1996 Audi A4 1.6

21st Feb 2020 7:50pm

Bill

Member Since: 18 Nov 2017
Location: Essex / Normandy
Posts: 1227

Just curious....

Does the start stop function the start motor/shorten life, or shouldn’t I worry? Filters are in fact so good that in certain circumstances, when the ambient air is already polluted, a diesel car will tend to extract more particles from the air than it emits. Emissions Analytics worked with........etc etc

He who dies with the most toys wins...

22nd Feb 2020 10:59am

Baltic Blue

Member Since: 13 Aug 2015
Location: North Wales
Posts: 3758

Having had a starter motor in pieces and seeing first hand how black and pitted the solenoid contacts get in normal non stop/start use they get, I can only presume that they get burned a bit every time they operate.
I would search out Stan’s post to disable it personally.
Mike.

G reg 2.5VM Vogue Portofino red 1991- 1999
V reg 2.5td P38 Rioja red 1999- 2006
53 reg td6 Vogue Oslo blue 2006- 2015
11 reg 4.4 TdV8 Vogue SE. Baltic blue 2015- date.
https://www.fullfatrr.com/forum/topic56162...tty+affair

22nd Feb 2020 11:13am

Bill

Member Since: 18 Nov 2017
Location: Essex / Normandy
Posts: 1227

I tend to switch it off as I start the car, not happy messing with the car as not technically competent.

Interestingly in a BMW I rented in scotland , the start engine button is surrounded by a switch off start stop button so you don’t forget to switch off the function !

To many stops and starts in that comment. Filters are in fact so good that in certain circumstances, when the ambient air is already polluted, a diesel car will tend to extract more particles from the air than it emits. Emissions Analytics worked with........etc etc

He who dies with the most toys wins...

22nd Feb 2020 11:21am

V8 Bob

Member Since: 15 Mar 2018
Location: Cumbria
Posts: 356

2012 Range Rover Westminster TDV8 Ipanema Sand

Took my old starter to bits out of curiosity and it had the same pitting on the solenoid terminals. The live feed being the main issue. 2012 tdv8 Westminster arrived Jan 19 gone Dec 23

200 TDi discovery bobtail gone
RR classic v8 bobtail gone
300 tdi Discovery 3 dr gone

22nd Feb 2020 11:49am

mpirie

Member Since: 26 Jun 2012
Location: In the Highlands
Posts: 898

2013 Range Rover Autobiography SDV8 Luxor

There's a whole other thread on replacing the starters on 4.4TDV8's with loads of pictures of the burnt terminals.

Mike

23rd Feb 2020 9:04am

dibber83

Member Since: 22 Sep 2012
Location: Taunton
Posts: 22

Quote:
There's a whole other thread on replacing the starters on 4.4TDV8's with loads of pictures of the burnt terminals.

Mike

Do you have a link for this? Trying to find as much info on changing these as possible. I’m Getting a slight smell of hot plastic on drives of half an hour so. In Shauns posts there is a heat shield on the starter which mine didn’t have. Can’t see it listed on parts sites either. Was this removed at some point? Or not fitted until a certain date? Or maybe my starter has been done before and the shield was not put back! Not sure if one of the cables or the breather is getting warm, or if there is just a bit of oil residue burning off (fingers crossed). 2012 4.4TDV8 AB
———————————
2016 Mercedes C350e
2003 TD6 Vogue
2010 Alpina D3 BT
2005 Audi A4 2.0TDi SLine
1973 Series IIa
2001 BMW 320
1996 Audi A4 1.6

23rd Feb 2020 9:50am

Page 1 of 9

All times are GMT

Jump to

< Previous Topic | Next Topic >

Posting Rules

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum