OK so went to remove one of the rear wheels and as the title says i cannot budge the locking wheel nut!!
had a 4ft bar on and stopped as worried i will shear it off or break locking nut removal tool. spent over an hour with no joy.

So i am now squirting WD40 down the back of it every couple of hours in hope this will help. I have not applied any heat yet as i do not want to knacker the wheel finish though this is looking like i will have no choice.

Any words of wisdom?  2012 Vogue 4.4 TDV8 - Current
2014 Navara V6 - Gone
2004 Vogue TD6 - Gone
Grand Cherokee - Gone
Discovery V8 (LPG) - Gone
Discovery TD5 - Gone

You might be better off with a proper penetrating fluid, WD40 is OK but it was never designed as a penetrating fluid as such. I'd agree not to go to far with trying to get the nut undone, especially as the locking tools tend not to be the strongest. 2011 TDV8 Vogue SE

Hot air gun or even hair dyer might work without damaging paint.

Take it down your local tyre shop, they get this all the time and are "usually" very good at getting them off...

Believe it or not a rattle gun is very good at getting them off, if you take it gentle the rattle effect will loosen the bolt, hopefully before the nut or locking key break,.

If it does break they will have some tools to get the rest of the nut off without damage to the wheel...

I do 99.9% of the work on my fatty but there are some things best left to the professionals with their tools and most importantly, their knowledge....

Get it done now while you can still drive it and before you get a flat...

Driving it home with 4 wheel nuts will be fine.

Good Luck  Pete
I now have permission from the boss to use Y.O.L.O. Enjoy life
__________________________________________________
2014 L405 Autobiography SDV8 4.4 Loire Blue Ebony interior
2011 L322 Vogue SE 4.4 TDV8 Baltic Blue. Sold
2012 L322 Autobiography 5.0 Supercharged Ipanema Sand Sold
2002 L322 Vogue 4.4 V8 Epson Green (Fatty Offroader) Sold
-Click for Project Fatty off roader-

Do yourself a favour and throw the lockers in the bin sir... Buy 4 standard nuts and away you go

Agree with Craig; any thief will laugh at those locking wheel nuts....usually the only person they delay/prevent removing the wheel, is the owner

Cheers

good advice new ones on order  2012 Vogue 4.4 TDV8 - Current
2014 Navara V6 - Gone
2004 Vogue TD6 - Gone
Grand Cherokee - Gone
Discovery V8 (LPG) - Gone
Discovery TD5 - Gone

After a tragic experience with a Volvo XC60 locker, I always replace them with plain nuts... Fun fact: Range Rover ones cost more than twice than Jaguar's!

Last edited by adara on 15th Jan 2021 1:56pm. Edited 1 time in total

Yep, having owned a D3 Disco where the locking wheel nut broke and just kept spinning when I was doing a wheel swap I am firmly in the “get rid of them” camp.

It took me 1.5 hours to finally get the locking wheel nut off on my driveway with a garage full of tools. I would have hated to imagine if it was 11 o’clock at night in the freezing rain on a small road on Dartmoor what it would have been like....

The first thing I did when I brought home Sylvia was to replace them with normal wheel nuts.

Jim

Cam-Tech-Craig wrote:

Do yourself a favour and throw the lockers in the bin sir... Buy 4 standard nuts and away you go

In my case the problem was not the locker it was that some had well over tightened them not just the locker all of them on that wheel. In all my working on cars i have NEVER come across a wheel nut a 5ft bar would not free off it was insane.
Still there off now threads cleaned up and wheel back on torqued to the correct setting.

And yes all the lockers are going ordered a set of wheel nuts today  2012 Vogue 4.4 TDV8 - Current
2014 Navara V6 - Gone
2004 Vogue TD6 - Gone
Grand Cherokee - Gone
Discovery V8 (LPG) - Gone
Discovery TD5 - Gone

If you have this problem again try slightly tightening the other four wheel nuts to release some pressure on the tight one.

Also never buzz gun the locking wheel nut, do this one by hand then torque first at 10% less torque than the others, then do the other four wheel nuts to full torque with out going back to the locking wheel nut, always means this one isn’t over tightened which can happen if tightened last.

Lastly, throw the locking wheel nuts in the bin... even if you can’t get the locking wheel nut off, thief’s can... easily and quickly, they are a waste of time and only cause issues. Just run normal wheel nuts all round 👍

Cam-Tech-Craig wrote:

Do yourself a favour and throw the lockers in the bin sir... Buy 4 standard nuts and away you go