![]() | Home > In Car Electronics (L322) > What is this?? |
![]() ![]() |
|
|
stan Site Moderator Member Since: 13 Jul 2010 Location: a moderate moderated moderator moderating moderately in moderation Posts: 35485 ![]() ![]() |
whatever you do dont cut the red wire..
|
||
![]() |
|
Highroller Member Since: 18 Jul 2016 Location: Hampshire Posts: 565 ![]() ![]() ![]() |
Looks like a Heath Robinsons attempt to construct a bluetooth / Radio amp?.
|
||
![]() |
|
MarkMurphy Member Since: 30 Oct 2022 Location: Cambridgeshire Posts: 16 ![]() ![]() ![]() |
Thanks for the replies, yes its in the left rear of my l322, where there is wiring hell, had the rangie for just over a week, gradually going through the list, haha |
||
![]() |
|
Haylands Member Since: 04 Mar 2014 Location: East Yorkshire Posts: 8374 ![]() ![]() ![]() |
Has it got a non standard head unit, those twisted pairs of wires look like the speaker wires that come out of the original amp, that looks like a basic amp setup maybe...
|
||
![]() |
|
Merchy Member Since: 14 Feb 2021 Location: North Wales Posts: 1214 ![]() ![]() ![]() |
Finding that must have been a nasty surprise |
||
![]() |
|
jimmie Member Since: 19 Jul 2014 Location: Warsaw Posts: 163 ![]() ![]() ![]() |
Passive crossover for the speakers. Allow connect and split signal to different speakers from single output from amplifier.
|
||
![]() |
|
MarkMurphy Member Since: 30 Oct 2022 Location: Cambridgeshire Posts: 16 ![]() ![]() ![]() |
Yes its got a Pioneer android touch screen thing in, it powers up every time i get in, dont know how to use it yet, Haha ![]() |
||
![]() |
|
Haylands Member Since: 04 Mar 2014 Location: East Yorkshire Posts: 8374 ![]() ![]() ![]() |
Depends if the head unit has a built in amp....
|
||
![]() |
|
p38arover Member Since: 16 Dec 2015 Location: Western Sydney Posts: 1544 ![]() ![]() |
I agree with Jimmie, it looks like a passive crossover for the speakers. Ron B. VK2OTC
|
||
![]() |
|
Haylands Member Since: 04 Mar 2014 Location: East Yorkshire Posts: 8374 ![]() ![]() ![]() |
Looks like it's a crossover then, whatever one of them is!!! I know little about ICE, I do know those wires are the speaker wires coming from the original amp, I cut them from the plug and wired them directly to the new head unit that had a built in amplifier.
|
||||
![]() |
|
mjdronfield Member Since: 04 Nov 2011 Location: Derbyshire Posts: 7865 ![]() ![]() ![]() |
A crossover splits the sound frequencies so the right frequency range goes to each speaker. You don’t really want low frequency bass being sent to a tweeter, or treble being sent to a subwoofer. They can’t produce the sound. The original system used an active system, so the crossovers were in the BM54 amp, and the circuits powered/driven by the 12v feed from the car. This makes the system much more efficient as all the amps power can then be used to drive the speakers. In a more normal passive system the crossovers tend to be on each speaker and the amp has to drive the circuits too, taking quite a bit of its power output and increasing its load.
|
||
![]() |
|
Haylands Member Since: 04 Mar 2014 Location: East Yorkshire Posts: 8374 ![]() ![]() ![]() |
Thanks Mark |
||
![]() |
|
MarkMurphy Member Since: 30 Oct 2022 Location: Cambridgeshire Posts: 16 ![]() ![]() ![]() |
I get radio noise like when the antenna isn't connected, so i know its connected, i was going to take out the crossover, because its a mess, but if i disconnect it, what would i have to use? |
||
![]() |
|
![]() ![]() |
|
All times are GMT |
< Previous Topic | Next Topic > |
Posting Rules
|
Site Copyright © 2006-2025 Futuranet Ltd & Martin Lewis
![](../images/layout/footer/disclaimer.gif)