Advertise on fullfatrr.com »

Home > Technical (L322) > Front suspension won't lower
Post Reply  Down to end
Page 1 of 1
Print this entire topic · 
Spongo



Member Since: 13 Sep 2022
Location: Doncaster
Posts: 7

England 2011 Range Rover Vogue SE 4.4 V8 Bonatti Grey
Front suspension won't lower

Ok so I have searched and not found anything for my specific issue, whenI try to adjust the suspension down say to access mode it ( this is at a standstill) drops the rear but not the front, it actually raises the from the I get the message that suspension is blocked and remove the obstruction. It will eventually go down if I drive around a bit.

Now I have serviced both front and rear valve blocks and its still happening, I have no suspension faults showing just the error message that says I need to remove the blockage.

Any ideas as its baking my noodle.

Post #685692 15th Feb 2024 4:58pm
View user's profile Send private message View poster's gallery Reply with quote
JMC



Member Since: 01 Feb 2009
Location: Aberdeen-Angus
Posts: 755

Scotland 2012 Range Rover Westminster TDV8 Orkney Grey

Sounds like a faulty height sensor. The older I get, the more I realise that people confuse wrinkles for wisdom Smile

Post #685701 15th Feb 2024 5:41pm
View user's profile Send private message View poster's gallery Reply with quote
Spongo



Member Since: 13 Sep 2022
Location: Doncaster
Posts: 7

England 2011 Range Rover Vogue SE 4.4 V8 Bonatti Grey

Update, I have done all the O rings in the front valve block, still the same. Height sensors appear to be working when checking using GAP tool.

Has anyone got a really good guide as to which valve operates and when including the valve block with the compressor housing?

I can make an informed guess but really want to know that I am correct.

Oh and I have never been able to calibrate the suspension at all, GAP tool is fully updated but when i try the guided process the suspension has never lowered on any corner, maybe related maybe not.

When I did the O rings on the front valve block ( and the rear some time ago) there was significant pressure in the system even though i did a full depressurisation could this be related?

Post #685971 19th Feb 2024 3:50pm
View user's profile Send private message View poster's gallery Reply with quote
mjdronfield



Member Since: 04 Nov 2011
Location: Derbyshire
Posts: 7802

United Kingdom 2011 Range Rover Vogue SE TDV8 Buckingham Blue

The workshop manual is in the Wiki for download, top right, under the fullfatrr banner.

Thumbs Up 2011 Range Rover Vogue SE 4.4 TDV8

Previous cars :
2003 Range Rover Vogue TD6
1999 Discovery Td5 ES
1995 BMW M5 3.8 6 speed
1992 Range Rover 3.9 Efi Vogue
1992 BMW M5 3.8
1988 BMW 735i SE
1989 Ford Sierra XR4x4 2.9i
1981 Ford Fiesta Supersport

Post #685974 19th Feb 2024 4:40pm
View user's profile Send private message View poster's gallery Reply with quote
mjdronfield



Member Since: 04 Nov 2011
Location: Derbyshire
Posts: 7802

United Kingdom 2011 Range Rover Vogue SE TDV8 Buckingham Blue



 2011 Range Rover Vogue SE 4.4 TDV8

Previous cars :
2003 Range Rover Vogue TD6
1999 Discovery Td5 ES
1995 BMW M5 3.8 6 speed
1992 Range Rover 3.9 Efi Vogue
1992 BMW M5 3.8
1988 BMW 735i SE
1989 Ford Sierra XR4x4 2.9i
1981 Ford Fiesta Supersport

Post #685976 19th Feb 2024 4:48pm
View user's profile Send private message View poster's gallery Reply with quote
Spongo



Member Since: 13 Sep 2022
Location: Doncaster
Posts: 7

England 2011 Range Rover Vogue SE 4.4 V8 Bonatti Grey

Thanks for that, I do have the workshop manual but alas it doesn't describe what happens to each valve etc. I think its fairly intuative, seems strange that its only the front that "sticks", to me if seems like a sticking valve but these cars can be fickle.

Thanks for the pictures they do at least make sense.

I am going to do the O rings on the valve block in the boot just in case this is the issue, if not I think its going to me local independent for some investigation.

Post #685981 19th Feb 2024 5:14pm
View user's profile Send private message View poster's gallery Reply with quote
will308f



Member Since: 19 Apr 2022
Location: plymouth
Posts: 417

United Kingdom 2014 Range Rover Autobiography SDV8 Loire Blue

Sounds like valve block could be sticking ,have you tried swapping the front and rear valve blocks around to see what happens ?.if the front then lowers and the rear doesn’t then you know it’s a valve block issue……you can pick them up from eBay (£15 ish)

Post #686022 20th Feb 2024 6:05am
View user's profile Send private message View poster's gallery Reply with quote
Spongo



Member Since: 13 Sep 2022
Location: Doncaster
Posts: 7

England 2011 Range Rover Vogue SE 4.4 V8 Bonatti Grey

Now why didn't i think of that Confused

Post #686031 20th Feb 2024 8:39am
View user's profile Send private message View poster's gallery Reply with quote
Spongo



Member Since: 13 Sep 2022
Location: Doncaster
Posts: 7

England 2011 Range Rover Vogue SE 4.4 V8 Bonatti Grey

Well after a few hours tinkering in the garage I solved the issue.

Fist I did the O rings on the valve block in the compressor housing and that didn't fix it, still the same the car would not lower at the front when commanded.

However when i de pressurised using the GAP tool the car did lower but very slowly and when I undid the unions on the valve block there was significant pressure remaining. So i did a little more digging here in the forum and found someone who was getting a similar issue in that the car would not lower at all and they found a blocked "muffler" on the outlet of the system, so I removed the muffler and hey presto suspension is working exactly as it should. I guess it was taking so long for the front to start dropping the computer decided there was an obstruction under the car.

So now at least all the valve blocks have been serviced and I have fixed the fault just need to get a replacement "muffler" now, thanks for all your help

Post #686061 20th Feb 2024 1:49pm
View user's profile Send private message View poster's gallery Reply with quote
will308f



Member Since: 19 Apr 2022
Location: plymouth
Posts: 417

United Kingdom 2014 Range Rover Autobiography SDV8 Loire Blue

Thumbs Up well at least the valve blocks will be good for a long time ,I'm sure that some where on here someone has said just to drill a 2mm hole in the muffler and its all sorted (quick fix till you can get a new one

Post #686069 20th Feb 2024 2:57pm
View user's profile Send private message View poster's gallery Reply with quote
mjdronfield



Member Since: 04 Nov 2011
Location: Derbyshire
Posts: 7802

United Kingdom 2011 Range Rover Vogue SE TDV8 Buckingham Blue

I was going to mention the exhaust on the air compressor, but as you said the rear lowered I didn’t think it was that. Nothing lowered when mine was blocked.

Got there in the end.

Thumbs Up 2011 Range Rover Vogue SE 4.4 TDV8

Previous cars :
2003 Range Rover Vogue TD6
1999 Discovery Td5 ES
1995 BMW M5 3.8 6 speed
1992 Range Rover 3.9 Efi Vogue
1992 BMW M5 3.8
1988 BMW 735i SE
1989 Ford Sierra XR4x4 2.9i
1981 Ford Fiesta Supersport

Post #686071 20th Feb 2024 3:53pm
View user's profile Send private message View poster's gallery Post Reply
Post Reply  Back to top
Page 1 of 1
All times are GMT

Jump to  
Previous Topic | Next Topic >
Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



Site Copyright © 2006-2024 Futuranet Ltd & Martin Lewis
fullfatrr.com RSS Feed - All Forums


Switch to Mobile site