The two bushes that sit in each of these lower arms, does anyone have a part number for them at all as my front ones are dying and squeaking like a mouse that's just found 2tons of lancashires finest crumbly cheese!!! 😬😬😬😬 FFRR MY06 facelift With TDV8 Alloys Zeros/ATR's
Mantec Sump Guard, Rigid Load liner, MY10 BT upgrade.

Rear as in rear of car or the arm behind the control arm RAVE calls a tie rod?

Rear of vehicle 👍 FFRR MY06 facelift With TDV8 Alloys Zeros/ATR's
Mantec Sump Guard, Rigid Load liner, MY10 BT upgrade.

The fronts bushes are probably RBX00070 and RBX000200 which supersedes to LR018345

Try using Rockauto.com for part numbers. I assume it is a US only company but it is great for looking up parts and cross reference for part numbers. I found this under suspension /control arm bushings MOOG K200836. Depends which one you need. They may all be the same for the rears.

RGX000060 front
RGX000071 rear

👍 There is nothing that can't be fixed with a hammer😜😜
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

This is one of the arms

http://www.island-4x4.co.uk/rear-lower-gen...34573.html

The part number you gave RL seems to just be pulling up bushes for the front end of the car

Think best thing to do is grab a picture of them both and ask Dan what the damage is going to be as may end up getting a pair of second hand arms and fit the new bushes to them and clean up so straight swap.
Though I was thinking of rear dampers I've just seen the cost of them  FFRR MY06 facelift With TDV8 Alloys Zeros/ATR's
Mantec Sump Guard, Rigid Load liner, MY10 BT upgrade.

Yep the ones I quoted should do it

Lrparts.ru is your friend for microcat and has the exploded diagrams you need. There is nothing that can't be fixed with a hammer😜😜
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

northernmonkeyjones wrote:

RGX000060 front
RGX000071 rear

👍

Thanks NMJ 👍 FFRR MY06 facelift With TDV8 Alloys Zeros/ATR's
Mantec Sump Guard, Rigid Load liner, MY10 BT upgrade.

Just seen that I can get the arms for £108 each and engine so if these include bushes I'll go for that option! FFRR MY06 facelift With TDV8 Alloys Zeros/ATR's
Mantec Sump Guard, Rigid Load liner, MY10 BT upgrade.

Looking at the microcat pic, it shows it with the bushes so it would appear that it does indeed include the rubber bits. Probably an easier job than pressing out the originals. There is nothing that can't be fixed with a hammer😜😜
FFRR 4.4 SDV8 Autobiography Santorini Black.
Fiat 500x 1.4 multiair Lounge 2015
2010 LR D4 Commercial 2.7 TDV6

That whole wishbone cost $325 US here. I found this nice reference pic on Amazon.

kingpleb wrote:

This is one of the arms




The part number you gave RL seems to just be pulling up bushes for the front end of the car

doclees wrote:

That whole wishbone cost $325 US here. I found this nice reference pic on Amazon.

Yes but it is a nice diagram for reference and often you can find the cross reference if you have some number. The hard part is that the different suppliers use different terminology for their part location and descriptions. Very frustrating.