Hi guys,

Do u mean wrap in carbon fibre?

Yes it's all going to get wraped in the 3m stuff,

Let's hope it turns out as I expect

Sal RANGE ROVER OVERFINCHED 4.2 S/C
FRONT BUMPER O/F
REAR BUMPER. O/F
BOOT SPOILER O/F
22" ALLOYS. O/F
STAINLESS STEEL EXHAUST O/F
CARBON FIBRE WING MIRRORS & A PILLARS & CENTRE CONSOLE

I was thinking of doing that as well but in a walnut to match my existing trim. Primarily the two strips either side of the gearbox tunnel and maybe the window switch pack. Its hard to find though..... Present :2008 TDV8 HSE
Gone Audi A5 2.7TDI
Gone Discovery 3 HSE
Gone Mercedes CLK
Gone Range Rover 2.5 DSE

@ googsy-There's a place in greenogue business park in rathcoole that does wrapping..u can go up to see their work, v good IMO..

Walnut carbon fibre!!!

Never seen or heard of it, but u never know.

Sal RANGE ROVER OVERFINCHED 4.2 S/C
FRONT BUMPER O/F
REAR BUMPER. O/F
BOOT SPOILER O/F
22" ALLOYS. O/F
STAINLESS STEEL EXHAUST O/F
CARBON FIBRE WING MIRRORS & A PILLARS & CENTRE CONSOLE

Why are you bothering to carbon fibre your neon screwdriver? You wont be able to see it light up?!
T

So that when it gets shoved up ur ,

It will slide in easier

Sal RANGE ROVER OVERFINCHED 4.2 S/C
FRONT BUMPER O/F
REAR BUMPER. O/F
BOOT SPOILER O/F
22" ALLOYS. O/F
STAINLESS STEEL EXHAUST O/F
CARBON FIBRE WING MIRRORS & A PILLARS & CENTRE CONSOLE

Thanks Lolo not far from me .


I have seen some wood adhesive vinyl on a few kitchen sites the stuff used to wrap kitchen unit doors etc and available in a high gloss. Would need to see it close up to see if it would do though. Look at option B in link below looks very similar to Walnut colour in RR Also a nice gloss black

http://www.24studio.co.uk/ss/landpage55.js...4Qod-w0bLg Present :2008 TDV8 HSE
Gone Audi A5 2.7TDI
Gone Discovery 3 HSE
Gone Mercedes CLK
Gone Range Rover 2.5 DSE

Yes I have seen that stuff, need to just test it actually stretches,

And is able to curve round edges without getting damaged, and to make sure

It doesn't scratch easy as well

Sal RANGE ROVER OVERFINCHED 4.2 S/C
FRONT BUMPER O/F
REAR BUMPER. O/F
BOOT SPOILER O/F
22" ALLOYS. O/F
STAINLESS STEEL EXHAUST O/F
CARBON FIBRE WING MIRRORS & A PILLARS & CENTRE CONSOLE

True about scratches but im sure the flexibilty would be fine especially if applied using a heat gun but at 5.99 a roll its bound to be worth a try. Failing that theres always Ronseals paint and grain  Present :2008 TDV8 HSE
Gone Audi A5 2.7TDI
Gone Discovery 3 HSE
Gone Mercedes CLK
Gone Range Rover 2.5 DSE

Last edited by Googsy on 18th Mar 2012 9:49pm. Edited 1 time in total

Gosh that was a little harsh.
I should be grateful you didnt mean the yellow screwdriver I guess!
Anyway I think it will all look good and watch with interest as have a skinning kit waiting to see action on door trims.
T

Today I did a bit of carbon fibre wrapping, it's not a easy as they make out especially on fiddly stuff like round the dials and the vinyl doesn't stick that well to the plastic. I have done the side strips either side of the centre console and the two lower dash panels - I will refit tomorrow and maybe post some photo's - but only if it looks nice  Geoff

looking forward to it Geoff Present :2008 TDV8 HSE
Gone Audi A5 2.7TDI
Gone Discovery 3 HSE
Gone Mercedes CLK
Gone Range Rover 2.5 DSE